Let's find the force of the water on a plate on the bottom of a pool. The plate is 2 m by 3 m, and the pool is 3 m deep. What's pushing down on the plate is the water standing on top of it.
Find the force on a 2 m by 3 m horizontal plate under 3 m of water
Text solution
Weigh the columnThe column on the plate holds 2⋅3⋅3=18 m3 of water, and each cubic meter weighs 1000⋅9.8=9800 N.
F=9800⋅(2⋅3⋅3)=176,400N
Pressure, the force on 1 m2The column on a 1 m by 1 m square is 3 m tall, so it holds 3 m3.
pressure=9800⋅3=29,400N/m2
Pressure at depth hOn a plate of area A at depth h, the column weighs 9800Ah. Dividing by A leaves 9800h, so only the depth matters.
So pressure depends only on depth. On a flat plate every point is at the same depth, so the force is that one pressure times the area.
Pressure at depth h
pressure=9800hN/m2
Total force on a horizontal plate
F=9800h⋅(area)
For another liquid, replace 9800 with that liquid's density times 9.8. In feet, 1 ft3 of water already weighs 62.4 lb, so at depth h feet the pressure is 62.4h lb/ft2 with no need to multiply by 32.
Any liquid
pressure=(density)⋅9.8⋅hN/m2
Water in feet
pressure=62.4hlb/ft2
2
Force on an upright plate
Now stand the same 2 m×3 m plate upright against the side of the pool, with its top edge at the surface and its bottom edge at depth h=3. Does the water still push on it with 176,400 N?
Still water pushes equally in every direction, sideways included, so the plate feels 9800h at depth h. But that runs from 0 at the top edge to 29,400 N/m2 at the bottom, so there's no one pressure to multiply by the area. A vertical strip has the same problem. A thin horizontal strip doesn't: every point on it is at one depth.
Find the force on a 2 m×3 m upright plate with its top edge at the water's surface
Text solution
One horizontal stripLike the slabs when we pumped water out of a tank, a horizontal strip keeps everything on it at one depth, so it has one pressure. Its area is 2dh.
force=9800⋅h⋅2dh
Add up the stripsThe strips run from the surface, h=0, down to h=3.
F=∫039800⋅h⋅2dh=9800⋅2[2h2]03=88,200N
F=∫039800⋅h⋅2dh=88,200N
Why it's half the flat plate's forceThe width is 2 all the way down and the pressure grows evenly, so the average pressure is the one at the middle depth, 1.5.
9800⋅1.5⋅(2⋅3)=88,200=21⋅176,400
That middle-depth shortcut works only because this plate's width is the same at every depth. For any other shape, we add up the strips.
For any vertical surface
F=∫9800⋅(depth)⋅(width)dh
3
When the width changes with depth
Now let's find the force of the water on a vertical triangular end of a trough. The triangle is 4 m wide at the water's surface and narrows to a point 2 m below, so each strip's width w depends on its depth. The sides are straight, so the width drops by the same amount, 2 m, for every meter we go down.
h=0:h=2:→w=4w=0w=4−2h
Find the fluid force on a triangular plate 4 m wide at the surface and 2 m deep, point down, then point up
Text solution
Point downIntegrate from the surface, h=0, to the point, h=2.
Point upNow the width starts at 0 at the surface and grows by 2 for each meter of depth, so w=2h.
F=9800∫02h⋅2hdh=9800[32h3]02=3156,800N
F=9800∫02h⋅2hdh=3156,800N
The middle depth doesn't work hereThe pressure at the middle depth, 1, times the area, 4 m2, matches neither triangle, because the width changes with depth.
9800⋅1⋅4=39,200N
The point-up triangle takes twice the force, with the same area and the same depths from 0 to 2. Its wide strips are down deep, where the pressure is largest. At depth 1.5, for example, the point-down triangle is only 1 m wide, while the point-up triangle is 3 m wide.
4
When the trough is only partly full
Now the same trough holds only 1 m of water. The top meter of the triangle is dry, so there's no force on it, and all of the force is on the bottom meter. The question is where to measure depth from.
Find the force on the triangular trough end when the water is 1 m deep
Text solution
Depth from the water's surfaceThe pressure is 0 at the waterline, so h=0 there. The waterline is halfway down the trough, where the width is 2.
h=0:w=2,h=1:w=0→w=2−2h,0≤h≤1
h=0:h=1:→w=2w=0w=2−2h,0≤h≤1
Total force
F=∫019800⋅h⋅(2−2h)dh=9800[h2−32h3]01=39800N
F=∫019800⋅h⋅(2−2h)dh=39800N
Why not from the trough's top?Measuring h from the top, with bounds 1 to 2, puts a pressure of 9800 N/m2 at the waterline, as if an extra meter of water stood above it. The answer comes out four times too large.
9800∫12h(4−2h)dh=4⋅39800N
5
A circular window below the surface
Now let's find the force of the water on a vertical circular window of radius 1 m whose center is 3 m below the surface.
With depth h measured from the surface, the circle is x2+(h−3)2=1, and the width has (h−3)2 under the square root. Putting the origin at the window's center, with y the height above it, makes the width simpler. But then a strip's depth isn't y. The center is 3 m down and the strip is y above it, so its depth is 3−y.
Depth h from the surface
2≤h≤4,w=21−(h−3)2
Height y above the center
−1≤y≤1,w=21−y2,depth=3−y
−1≤y≤1,w=21−y2depth=3−y
Find the force on a vertical circular window of radius 1 m with its center 3 m below the surface
3
1
Text solution
Split the integralMultiplying the depth 3−y by the width gives two pieces.
F=9800[3∫−1121−y2dy−∫−11y⋅21−y2dy]
F=9800[3∫−1121−y2dy−∫−11y⋅21−y2dy]
The first piece is the areaAdding up the strips' areas, width times dy, across the window gives its area. Trig substitution gives the same.
∫−1121−y2dy=2⋅2π=π
The second piece is 0The strips at y and −y have the same width, but 2y1−y2 changes sign, so they cancel.
F=9800(3π−0)=29,400πN
Each strip above the center pairs with a strip of the same width below it, and their depths, 3−y and 3+y, average to 3. So the force is the pressure at the center times the area of the window.
2.5
3.5
y
0
3
3
∫−11y⋅21−y2dy=0
F=(9800⋅3)⋅π
Is a strip’s coordinate always its depth?
Summary
Pressure at depth h and force on a horizontal plate
h
Water in meters, and force on a horizontal plate
pressure=9800hN/m2
F=9800h⋅(area)
Another liquid, and water in feet
pressure=(density)⋅9.8⋅h
pressure=62.4hlb/ft2
In still water, pressure depends only on depth. At depth h meters, the pressure is 9800h N/m2, from the water's density of 1000 kg/m3 times 9.8 m/s2. For another liquid, multiply its density by 9.8 and by h. In feet, 1 ft3 of water already weighs 62.4 lb, so we don't multiply by 32.
When a plate is horizontal at depth h, every point is at the same depth, so the pressure is constant across the entire plate. The total force is just pressure times area.
Force on an upright plate
h
dh
w
F=∫9800⋅(depth)⋅(width)dh
On an upright plate, depth changes from top to bottom, so pressure changes too. Slice the plate into thin horizontal strips of thickness dh. Every point on a horizontal strip is at the same depth h, so it has one pressure, 9800h. The force on one strip is 9800⋅(depth)⋅(width)dh, and integrating adds up the force from all the strips.
Measuring depth from the water's surface
depth=D−y
Always measure depth from the water's surface, where pressure is 0. Measuring from the top of a trough that's only partly full adds pressure for water that isn't there. The bounds are the depths at the top and bottom of the submerged part of the plate.
When we measure y upward from a point at depth D below the surface, a strip at height y is y meters closer to the surface, so its depth is D−y. For a submerged circular window whose centre is 3 m below the surface, setting y=0 at the centre gives depth 3−y.
Finding the width of a strip
Straight sides
h=0:h=2:→w=4w=0w=4−2h
Curved edges
x2+y2=r2y=x2→w=2r2−y2→w=2y
x2+y2→w=r2=2r2−y2
y→w=x2=2y
For a plate with straight sides, the width changes at a constant rate with depth, so you can write w directly from the widths at two known depths. For the triangular plate with width 4 at the surface and 0 at depth 2, the width decreases by 2 for each meter of depth, so w=4−2h.
When an edge is curved, solve its equation for x to find the width from the left edge to the right edge. For a circle of radius r with its centre at the origin, x=±r2−y2, so a horizontal strip at height y has width 2r2−y2. For y=x2, the width from −y to y is 2y.
Symmetry on a submerged circle
∫−rr2r2−y2dy=πr2
∫−rry⋅2r2−y2dy=0
When a circular plate is completely submerged and y is measured up from its centre at depth D, the depth of a strip at height y is D−y. Multiplying D−y by the width splits the force integral into D∫wdy minus ∫y⋅wdy. The first integral adds up the areas of the horizontal strips, giving the circle's area, πr2.
The second integral is 0. A strip at height y and a strip at −y have the same width, but the factor of y has opposite signs for the two strips, so their contributions to the second integral cancel. This only works for the whole circle, from −r to r. The total force on a submerged vertical circle is just the pressure at its centre times its area.
6
Practice
Give exact answers. When lengths are measured in meters, the force is in newtons (N). When lengths are measured in feet, the force is in pounds (lb).
1
A rectangular window 6 ft wide and 3 ft tall is set in the vertical wall of an aquarium, with its top edge 2 ft below the surface of the water. Water weighs 62.4 lb/ft³. Find the force of the water on the window.
Depth h is measured down from the water's surface. What is h at the top of the window, and what is h at the bottom?
In feet, is 62.4 lb/ft3 a mass or a weight? Do we need to multiply it by 32?
If you got 125,798.4 lb Pounds are already a unit of weight, so don't multiply 62.4 by 32.If you got 1684.8 lb Depth is measured from the water's surface, not from the top of the window. The top of the window is already 2 ft down.
Bounds and pressureThe window starts 2 ft down and is 3 ft tall, so h runs from 2 to 5. Pounds are already a unit of weight, so the pressure at depth h is 62.4h lb/ft2.
2≤h≤5,w=6,pressure=62.4hlb/ft2
2≤h≤5,w=6pressure=62.4hlb/ft2
Total forceEach horizontal strip has area 6dh, so we integrate pressure times area from h=2 to h=5.
F=∫2562.4⋅h⋅6dh=62.4⋅3[h2]25=62.4⋅3⋅21=3931.2lb
2
A triangular plate with a base of 6 m and a height of 3 m hangs vertically in water, point up. Its point is 1 m below the surface, and its base is horizontal, 4 m below the surface. Find the force of the water on one side of the plate.
What is the width of the plate at h=1, and what is it at h=4?
The width increases from 0 to 6 as depth increases by 3 m. How much does the width increase per meter of depth?
If you got 411,600 N Check the width formula at the top point. At h=1, the width should be 0, not 2.If you got 176,400 N Check where depth is measured from. The top point is 1 m below the surface, so h goes from 1 to 4, not 0 to 3.
Width at depth hThe plate widens from w=0 at h=1 to w=6 at h=4, so its width increases by 2 m for each meter of depth.
h=1:w=0,h=4:w=6→w=2(h−1),1≤h≤4
h=1:h=4:→w=0w=6w=2(h−1),1≤h≤4
Total forceMultiply pressure 9800h by strip area 2(h−1)dh and integrate across the plate, from h=1 to h=4.
A cylindrical tank of radius 2 m lies on its side and is half full of water. Find the force of the water on one circular end of the tank.
The tank is half full, so the water's surface passes through the center. What is the range of depth h?
A circle of radius 2 centered at the origin satisfies x2+h2=4. For a given depth h, what is the horizontal distance from the left edge to the right edge?
If you got 78,400/3 N4−h2 is only half the strip's width, from the center to the edge. Double it for the full width.
Width of a stripThe water only touches the bottom half of the circle, from depth h=0 down to h=2, and each strip stretches from x=−4−h2 to x=4−h2.
x2+h2=4→w=24−h2,0≤h≤2
x2+h2=4→w=24−h20≤h≤2
Set up the integralThe force on a strip at depth h is pressure 9800h times area 24−h2dh.
F=9800∫02h⋅24−h2dh
Evaluate by substitutionThe derivative of 4−h2 is −2h, so we use the substitution u=4−h2.
u=4−h2,du=−2hdh,h=0→u=4,h=2→u=0
u=4−h2,du=−2hdhh=0→u=4,h=2→u=0
F=9800∫04udu=9800⋅32⋅8=3156,800N
4
The end of a trough is the region between y=x2 and y=4, with lengths in feet. The trough is full of water, which weighs 62.4 lb/ft³. Find the force of the water on one end of the trough.
The water's surface is at y=4. What is the depth of a strip at height y?
The boundary curve is y=x2. At height y, what are the x-coordinates of the two edges?
If you got 1597.44 lb The water's surface is at y=4, so a strip at height y is at depth 4−y, not y.
Width and depthThe curve y=x2 gives edges at x=±y, so the width is 2y, and the depth below y=4 is 4−y.
y=x2→x=±y→w=2y,depth=4−y,0≤y≤4
y=x2→x=±y→w=2ydepth=4−y,0≤y≤4
Total forceAt height y, the pressure is 62.4(4−y), so we integrate pressure times area from y=0 to y=4.
A swimming pool is 10 m long and full of water. It is 1 m deep at the shallow end and 3 m deep at the deep end, and its bottom slopes in a straight line from one end to the other. Find the force of the water on one of the long vertical side walls. (Challenge)
For depths h between 1 and 3, does the strip run the whole 10 m length of the pool?
The bottom slopes from depth 1 m at the shallow end to depth 3 m at the deep end. At what horizontal distance x from the shallow end does the bottom reach depth h?
If you got 441,000 N The width is only 10 m for the top 1 m of depth. Below h=1, the sloping bottom makes the width shorter than 10 m.
Width in the top meterThe shallow end is 1 m deep, so from h=0 to h=1, the water touches the full 10 m length of the wall.
0≤h≤1:w=10
Width along the sloping bottomThe bottom depth increases by 2 m over a length of 10 m, so the bottom reaches depth h at distance x=5(h−1) from the shallow end. That leaves a width of 10−x to the deep end.
1+5x=h→x=5(h−1),w=10−5(h−1)=5(3−h),1≤h≤3
1+5x=hw1≤h→x=5(h−1)=10−5(h−1)=5(3−h)≤3
Total forceSplit the force integral at h=1 to use the two width formulas.